The banner above is an advertisment - if it asks you to download software, please ignore.
Site News - 3/26 M Car Covers (by State of Nine) | 12/12 Make Amazon Pay Saabnet!
Date: Sat, 10 Apr 2004 22:01:25 +0100
From: "Murphwiz" <murphwiznospamMEOUTTOOhotmail.com_REMOVEMESPAMMERZ>
Subject: Re: WIS Info Needed


"Ben" <benm_No_SpamnospamMcgill.No.Spam.ca> wrote in message news:flqf70l2qjfo78br788cek1r5gb06g4hkanospamcom... > Hi fellows, > > Does anybody have he WIS info or replacing a oil pan on a Saab 1999, > model 9-3, engine B204L? > Oil sump To remove (in car) 1. Remove the dipstick and put a cloth in the pipe. Suspend the engine from the lifting beam, part no. 83 94 850. Disconnect the oxygen sensor cable. Remove the heat shield (turbo). 2. Raise the car, drain the engine oil and position the lifting trolley under the engine. 3. Remove the front wheels and the air shields. Undo the joint between the front exhaust pipe and the intermediate pipe. 4. Unscrew the front exhaust pipe from the exhaust manifold or, alternatively, from the turbocharger. Detach the three way catalytic converter from its mounting and remove the exhaust pipe. 5. Unscrew the nuts on both sides of the end piece and the rear engine mounting. Raise the lifting trolley, undo the remaining bolts and remove the subframe. 6. Remove the protective plate and oil sump. Leave the guide sleeve in the cylinder block. Wipe up any oil that has dripped out. To fit (in car) 1. Check that there are no impurities or other foreign matter in the sump and clean the sealing surfaces with benzine. 2. Apply an even bead of flange sealant, part no. 93 21 795, to the sealing surface of the oil sump and fit the oil sump. Tightening torque: 22 Nm (16.2 lbf ft) 3. Fit the protective plate. 4. Lift up the subframe and bolt it in place. Tightening torques: Front: 115 Nm (85 lbf ft) Centre: 190 Nm (140.6 lbf ft) Rear: 110 Nm + 75ƒ (81.4 lbf ft + 75ƒ) 5. Fit and tighten the nuts on the end piece. Tightening torque: 75 Nm (55.5 lbf ft) 6. Clean the area for the joint in the exhaust pipe. 7. Fit the front exhaust pipe to the exhaust manifold or, alternatively, to the turbocharger. Lubricate the studs on the turbocharger with Molycote 1000 before fitting. 8. Suspend the three way catalytic converter and screw together the joint between the front exhaust pipe and the intermediate pipe. 9. Fit the air shields and wheels. Tightening torques: Wheels: 110 Nm (81 lbf ft) 10. Make sure the oil plug is tight. Lower the car and fill with engine oil. Put back the dipstick and connect the oxygen sensor cable. Fit the heat shield (turbo). 11. Remove the lifting beam, warm up the engine and check for leaks from the sealing surfaces. -- Why not give the forums a try?! www.saabs.info www.nospam.com www.saabtrackday.co.uk

Return to Main Index
StateOfNine.com
SaabClub.com
Jak Stoll Performance
M Car Covers
Ad Available

The content on this site may not be republished without permission. Copyright © 1988-2024 - The Saab Network - saabnet.com.
For usage guidelines, see the Mission & Privacy Notice.
[Contact | Site Map | Saabnet.com on Facebook | Saabnet.com on Twitter | Shop Amazon via TSN | Site Donations]