Re: Code 11 - Saab 9-5 Bulletin Board - Saabnet.com
The banner above is an advertisment - if it asks you to download software, please ignore.
Site News -
4/9 Saab Owners' Convention Day Pass Raffle |
3/26 M Car Covers (by State of Nine)
[General |
Members |
C900 |
9000 |
NG900 & OG93 |
93 |
95 |
NG95 |
99 |
Sonett |
Vintage Models |
Clubs |
Other Cars |
FAQs |
Gifts |
Member Photo Galleries |
Member Directory |
Classifieds |
Manuals |
*Buddy Registry |
*Mileage Registry |
Polls |
What's New |
Raffle |
Photo of the Month |
Sponsors]
[Main 95 Bulletin Board | BBFAQ |
Prev by Date | Next by Date | Post Followup ]
Member Login / Signup - Members see fewer ads. - Latest Member Gallery Photos
Re: Code 11
Posted by BrianS (more from BrianS) on Sun, 3 Jul 2005 10:37:18
In Reply to: Re: Code 11, Tom S., Sun, 3 Jul 2005 06:30:37
Members do not see ads below this line. - Help Keep This Site Online - Signup
In the front passenger footwell, first remove the cover by your left foot that held on by three plastic rivets. Then remove the panel below the glovebox (4 Torx-head screws), and then remove the glovebox (6? Torx-head screws). There are two stepping motors on the right-hand side of the air distribution unit and they're located next to each other. The one I replaced was the lower one which has a cover over it marked with an "R" and maybe a white line painted through it. The other stepping motor isn't covered so you see it easily. Two screws (#2 Philips or 6mm nut driver) hold the motor in place and a 6-pin electric connector. Once you remove the two screw just pull the motor straight out. You'll feel a little resistance but that's just flap pressure against the shaft.
The motor shaft is keyed so lift the flap linkage arm to make sure the motor line's up as your pushing it in. It's hard to explain but will be obvious when you're doing it. You'll also need to transfer the motor cover from the old one to the new one - very easy. Once the new motor is installed, plug in the connector, and run the calibration again a couple more times to make sure no codes appear. Install glovebox, panel, cover, and smile at the money and time you just saved from taking it to a dealer.
I would have put together something more formal with pics but didn't think of it until after the job was completed and I tossed to bad motor in the garbage. Stepping motor part number is 5172580. Hope this helped.
posted by 68.71.24...
Posts in this Thread:
- Code 11, BrianS, Sat, 2 Jul 2005 13:59:50
- Re: Code 11, mlc , Mon, 4 Jul 2005 18:06:55
- Re: Code 11, conradblack, Mon, 4 Jul 2005 15:50:19
- Re: Code 11, sallye, Sun, 3 Jul 2005 07:10:45
- Re: Code 11, Tom S., Sun, 3 Jul 2005 06:30:37
- Re: Code 11, BrianS, Sun, 3 Jul 2005 10:37:18 <-- Viewing This Message
Members do not see ads below this line. - Help Keep This Site Online - Signup
Post a Followup
No Site Registration is Required to Post - Site Membership is optional (Member Features List), but helps to keep the site online
for all Saabers. If the site helps you, please consider helping the site by becoming a member.
StateOfNine.com
|
SaabClub.com
|
Jak Stoll Performance
|
M Car Covers
|
Ad Available
|
Random Saabnet.com Member Gallery Photos (Click Image)
This is a moderated bulletin board - Posting is a privilege, not a right.
Unsolicited commercial postings are not allowed (no spam). Please, no For Sale or Wanted postings, SERIOUSLY.
Classifieds are to be listed in The Saab Network Classifieds pages.
This is a problem solving forum for over 250,000 Saab owners, so expect to see
problems discussed here even though our cars are generally very reliable. This is not an anything goes
type of forum. Saabnet.com has been a moderated forum since 1988. For usage guidelines, see the
Saabnet.com Mission and Purpose Page. Please remember that you are
not anonymous. Site Contact | Site Donations | Other Sites by SP -
Poverty2Prosperity.org | Run Club Menlo Park | ScreenBot
Site Members do not see red text instructions, bottom of the page anchor ads, or box ads.
Click here to see all
the Site Membership Benefits!