Oil pressure sender not a bad job (99 9-3) - Saab NG900 & OG9-3 Bulletin Board - Saabnet.com
The banner above is an advertisment - if it asks you to download software, please ignore.
Site News -
5/28: SAAB Evolutions/TSN T-Shirts $14 |
5/23: SOC Day Pass Winners Announceed
[General |
Members |
C900 |
9000 |
NG900 & OG93 |
93 |
95 |
NG95 |
99 |
Sonett |
Vintage Models |
Clubs |
Other Cars |
FAQs |
Gifts |
Member Photo Galleries |
Member Directory |
Classifieds |
Manuals |
*Buddy Registry |
*Mileage Registry |
Polls |
What's New |
Raffle |
Photo of the Month |
Sponsors]
[Main NG900 & OG93 Bulletin Board | BBFAQ |
Prev by Date | Post Followup ]
Member Login / Signup - Members see fewer ads. - Latest Member Gallery Photos
Oil pressure sender not a bad job (99 9-3)
Posted by dchmiele1992 [Email] (more from dchmiele1992) on Tue, 19 Jun 2007 05:33:43
In Reply to: Oil pressure sender, ARHsaab, Mon, 18 Jun 2007 18:40:37
Members do not see ads below this line. - Help Keep This Site Online - Signup
I replaced my oil pressure sender because the gasket on the sensor was leaking, causing a slow oil drip onto my exhaust. I got sick of the burning rubber smell and decided to replace it.
The oil pressure sending unit is on the backside if the engine. I have a 99 9-3, so your mileage may vary on a 900. Good news: the part is cheap, under $10 if I remember correctly. Bad news: you may have to buy a socket that is the right size to remove the sender, and the replacement sensor that you get may or may not have the same head size (even if its threaded the same).
I had to jack the front end and move the oil filler pipe out of the way to get the sending unit. The oil filler pipe is accessible from the top. If you remove the black plastic cover over the throttle body, there is a bracket with two hex head screws that holds the upper half of the filler pipe in place. if you remove the bracket, you can lift up the filler tube a few inches, which is enough to get it out of the way. There is a second bracket on the back side of the engine (which is accessed from below) that secures the bottom half of the filler tube to the engine. You can probably get at the sending unit without it, but its easier if you remove it. The sending unit has a single push-on electrical connector that you simply pull off to remove. The sending unit simply unscrews with the appropriate socket(the plug on top of the sending unit may interfere with the depth of your socket). Screw the new one in and put it all back together.
Best of luck
posted by 136.237.60...
Posts in this Thread:
Members do not see ads below this line. - Help Keep This Site Online - Signup
Post a Followup
No Site Registration is Required to Post - Site Membership is optional (Member Features List), but helps to keep the site online
for all Saabers. If the site helps you, please consider helping the site by becoming a member.
StateOfNine.com
|
SaabClub.com
|
Jak Stoll Performance
|
M Car Covers
|
Ad Available
|
Random Saabnet.com Member Gallery Photos (Click Image)
This is a moderated bulletin board - Posting is a privilege, not a right.
Unsolicited commercial postings are not allowed (no spam). Please, no For Sale or Wanted postings, SERIOUSLY.
Classifieds are to be listed in The Saab Network Classifieds pages.
This is a problem solving forum for over 250,000 Saab owners, so expect to see
problems discussed here even though our cars are generally very reliable. This is not an anything goes
type of forum. Saabnet.com has been a moderated forum since 1988. For usage guidelines, see the
Saabnet.com Mission and Purpose Page. Please remember that you are
not anonymous. Site Contact | Site Donations | Other Sites by SP -
Poverty2Prosperity.org | Run Club Menlo Park | ScreenBot
Site Members do not see red text instructions, bottom of the page anchor ads, or box ads.
Click here to see all
the Site Membership Benefits!